Our website is currently undergoing upgrading maintenance. We apologize for the inconveniences caused and will bring the new website to serve you better on 28 Nov 2018. Due to the upgrading works, the function – “Find a Distributor” and “Contact Us” page are currently not available. To locate our distributor or to make an inquiry, please call us at +603-6038 9498/97.
Saint-Gobain Weber Malaysia Shall ensure that the collection, use and Disclosure of your personal data is consistent with the Malaysia Personal Data Protection Act 2010 ("PDPA') and the relevant Privacy Laws in place in each jurisdiction that Saint-Gobain Weber Malaysia operates in. It is acknowledge that personal data collected and processed is obtained voluntarily and with your consent, please read our Company's Privacy Policy

Weber Saint-Gobain - Official website of the company

BELCEM HYDRO SEAL

BELCEM HYDRO SEAL
BELCEM HYDRO SEAL

Product benefits

Ready to use transparent, thin liquid solvent based impregnator for water repellent protection for stone surfaces. Suitable for bottom  & side surfaces only.


•Reduces water permeability of treated surfaces; therefore eliminate 
 developments of water stains.
•Protects trated surface from weathering.
•Minimize the appearance of efflorescence on both surfaces & joints.
•Seals & protects against staining or discoloration.
•Allows easier maintenance of treated surface by allowing easier removal of 
 graffiti, grmes, dirt, dust etc.
•Unaffected by ultra violet rays.
•Non-yellowing
•Easy to apply using brush, cloth or roller.
•Fast drying and able to support foot traffic within 24 hours.

Product Features

Technical Data

•Application Temperature : 5-30⁰C
•Touch dry time : 2 - 4 hours
•Cure Time : 24 hours
•Flash Point (ASTM D56) : 35⁰C
•Density : 0.80 g / cm³

Documentation

Printable Product Document (PDF)

Technical Data Sheet

Material Safety Data Sheet

Send or download the documentation

You can either send the documentation to en-email address, or download it.

Preparation & Application

Application

•Stir BELCEM HYDRO-SEAL well, before use.
 No further dilution is required.
•Surface must be dry, sound, flat/true & free of contaminants.
•Preliminary testing on small trial areas is important to determine coverage
 and compatibility if BELCEM HYRO-SEAL with the materials to be treated.

•Do not apply on damp or wet surfaces and during wet weather conditions.
•Apply to the underside, edges (4 sides).
•Apply evenly with a brush, cloth or roller, ensure that thin
 even coats are applied.

•Applied as a single coat treatment. Certain materials may require two or more
 coats for effective water & oil repellent result.

•Generally, low porosity (dense) material normally required 1 - 2
 coats treatment;porous material required two or more treatment coats.
•Where a second coat is required, allow first coat to impregnate into the
 Natural Stone Slab, within 30 - 60 minutes, before applying the
 second coat in  similar manner.

•The second coat must be applied wet on wet; before first coat dries out
 or fully cure.
•1 - 2 hours after application of final coat,buff off (polish) any residue of
 BELCEM HYDRO-SEAL on the top surface by a clean dry absorbent cloth.
•Achieves maximum properties in 5 days.

•Treated Natural Stone Slab should only be installed after 24 hours.
•Adequate protection from weathering & traffic must be provided during
 application and while BELCEM HYDRO-SEAL had yet to cure.

Self Life & Storage

•12 months after manufacturing date when stored unopened in dry condition of normal ambient temperature.

Coverage

Depending on porosity of material to be sealed :
   
Low water absorption (< 5%)                  = 1 - 2 ltrs / 100 m²
Moderate water absorption (20-30%)      = 3 - 5 ltrs / 100 m²
High water absorption (35-50%)              = 7 - 10 ltrs / 100 m²

Packing

Available in 1, 5 & 20 ltr steel container.

packaging

1,5 & 20 Ltrs