Saint-Gobain Weber Malaysia Shall ensure that the collection, use and Disclosure of your personal data is consistent with the Malaysia Personal Data Protection Act 2010 (‘PDPA’) and the relevant Privacy Laws in place in each jurisdiction that Saint-Gobain Weber Malaysia operates in.
It is acknowledge that personal data collected and processed is obtained voluntarily and with your consent. Please read our Company's Privacy Policy.

Weber Saint-Gobain - Official website of the company

weberset eco flex

BELCEM ECO-FLEX

weberset eco flex
weberset eco flex

Product benefits

  • Single component, mixing with clean water only;allow for easier on-site mixing.

Eco-Friendly & CO2 Emission reduced Class C2 S1 "Green" Cement-Based Tile Adhesive,comply with Singapore Green Label (SEC) Green Label Criteria(GLS 022),minimum 20% Recycled content. 

 

  • Specially formulated for the installation of Porcelain or Vitrified Homogeneous Tiles or other tiles or natural stone with low water absorption rate(Ie.<0.5%) and for installation onto demanding substrate.

Product Features

Technical Data

  • Application Temperature : Above 5⁰C - 50⁰C
  • Working Time(Pot Life) : 3-4 hour
  • Open time : 15-20 minutes at 25⁰C
  • Setting Time : Initial = 8 hours, Final = 16-20 hours
  • Recommendation Thickness : 6-12mm 

Documentation

Printable Product Document (PDF)

Technical Data Sheet

Material Safety Data Sheet

Send or download the documentation

You can either send the documentation to en-email address, or download it.

Preparation & Application

Substrate Preparation

Substrate must be dry, sound, flat/true & free of contaminants. 

Adhesive Preparation

  • 1 pbw water to 3 pbw adhesive (7-8 ltrs Water or Latex Admixture to 25kg weberset eco flex )
  • Mix weberset eco flex with water (or weber rage Latex Admixture) as per the recommended mix ratio. Mechanical mixing recommended.
  • Do not mix cement and or sand to Adhesive mixture. 

Application

step 1
step 2
step 3
step 4
  • Spread adhesive to the substrate at bed thickness of 6-12mm (may vary depending on tile size & thickness) with suitable notched trowel. 


  • Spread no more than 1m² at a time to avoid Skin-Over. Open time of spread adhesive is approx.15-20 minutes. 


  • Promptly fix tiles onto adhesive bed, followed by slight twisting action to ensure good contact. 


  • Lay tiles on the adhesive and press firmly or knock gradually with rubber hammer in order to spread the notch of adhesive equally. 


  • Allow to set for 24 hours; before grouting commences. Allocate joints of approx.3mm wide between tiles. 


  • Remove surplus adhesive from tile surface & joints before it hardens. 

Recommendation for Tiling

Avoid applying the adhesive in lumps (as shown in the picture) at the tile back. This will create voids underneath the tiles, which could lead to the tile fragility and water permeation

Recommendation for Grouting

•To maintain straight joints, spacers should be used (as shown in the picture).  The joint width is controlled by the width of spacer.
•At least 24 hours after completion of tiling or until adhesive had set. Setting may be delayed on dense or impervious surfaces.
•Allocate joints of approx. minimum 3mm wide between tiles. Joints width may vary depends on tile size.

Self Life & Storage

6 months after manufacturing date when stored unopened in dry condition of normal ambient temperature.

Type of substract/surface

Concrete, Cement-Sand Render/Screed, Existing Tile (mix with Belle's Range of admixture),Sheets & Boards including Vinyl (prime surface with BELBOND SBR & mix Product with BELCEM ADMIX I)

Tiles preparation

Ensure that tiles are clean, dry, free from grease, dust, or any other contaminations 

packaging

25 kg